|
(Old) Mac versions
Does anyone know what the difference is between the ordinary and pro versions?
Russell666
,
7/27/2010 12:00:00 AM(UTC)
|
8
|
399
|
Mark-101
1/9/2012 12:00:00 AM(UTC)
|
|
|
(Old) Adding Bat and Board outside siding using latest version on MAC
I am searching for a traditional bat and board vertical siding common in barn construction and can't find it. Also I am trying to have different siding for the peaks - how do I do this if I have a wall with the peak included in it - not two walls on to
Simson, Bill
,
12/6/2011 12:00:00 AM(UTC)
|
0
|
178
|
|
|
|
(Old) Upgrade from 14.14 to 15?
What is the upgrade path from 14 to 15 for the Mac?
romley, steve
,
4/18/2011 12:00:00 AM(UTC)
|
0
|
173
|
Patricia G.
11/27/2011 12:00:00 AM(UTC)
|
|
|
** Designing interior rooms and viewing them in 3D
I am trying to design the interior rooms but don't have the all the options to drop in hardwood floors while I am in 2D mode. I want to view what I have done in 3D mode for interior space but cannot find how to do it. Do I have to remove the roof, and re-
Martin, Sonnie
,
11/20/2011 12:00:00 AM(UTC)
|
0
|
132
|
|
|
|
(Old) Foundation Walls
I am trying to add a 2ft concrete foundation wall around the entire perimeter of the bungalow I designed, but am unable to. Any ideas !!
Martin, Sonnie
,
11/16/2011 12:00:00 AM(UTC)
|
0
|
114
|
|
|
|
** Need floor plan for a bi-level split foyer house
I want to design the floor plan for my bi-level house, but I don't want to start from scratch. From what I have read, the house I have is a typical bi-level house built in the 1960s. It has two floors. The foyer has two set of stairs. The attached garage
funnychap
,
10/31/2011 12:00:00 AM(UTC)
|
0
|
167
|
|
|
|
(Old) Dormer Cutouts
After about 20 hours I finally got my dormer looking good on a 12/12 roof.It's 20 foot wide with a sliding patio door. Now after 6 hours I can't get the roof cutout.The manual is not very clear on how to do this. I keep geting a message (Make sure dormer
A., Dave
,
10/25/2011 12:00:00 AM(UTC)
|
0
|
216
|
|
|
|
(Old) 1st,2nd & 3rd Floors floating in mid-air?
Hi I drew my three floors an went to Elevation Editor,and 3D. All three were floating in mid-air. The first floor I used as a concrete foundation(2ft.) The second is the living space(10ft tall walls)the third is my 12/12 gable roof area that is 1/2 story
A., Dave
,
10/23/2011 12:00:00 AM(UTC)
|
0
|
141
|
|
|
|
(Old) Plumbing and electrical wiring
Hi, I have HDS 14.1.7 and find it easy and very good. However I need to add electrical wiring runs and plumbing pipes as well as the plugs sinks etc. Surely this should be easy, all it needs is the ability to draw connecting lines of various colours.
King, Bob
,
9/12/2011 12:00:00 AM(UTC)
|
0
|
131
|
|
|
|
(Old) Not able to drag materials to - anywhere.....
{MAC user}....I keep trying to drag the materials {brick, specifically} to an outside wall, and NOTHING happens.....I tried this with other materials also, and again, nothing. I think I'm doing exactly what the instructions said, but I don't know why not
Coffman, Robin
,
9/12/2011 12:00:00 AM(UTC)
|
0
|
128
|
|
|
|
(Old) How to I draw rooms with exact size?
I am trying to draw rooms with exact size e.g. 6.15 m x 5 m, 6.1 m x 4.1 m, 3.65 m x 5 m, etc. I tried editing the size of the walls one by one but after a while the walls start to disconnect or are not straight any more. Any clue on how to draw these wit
Thumoe
,
8/15/2011 12:00:00 AM(UTC)
|
0
|
157
|
|
|
|
(Old) Automatic dimensions for rooms added in quick start not updating
I am using HLDS Pro 15 for Mac. I created a set of rooms in Quick Start and then hit continue to move into floor view. I changed the dimensions of one of the rooms, but the automatic dimensions for that room on the outside of the drawing are not updatin
Toews, Philip
,
8/7/2011 12:00:00 AM(UTC)
|
0
|
132
|
|
|
|
** Product manual
I downloaded the product so I did not receive any manual (that I know of). The tutorial and in-program help is limited. Is there anywhere to get a full manual online. This program is not as intuitive as I was lead to believe.
dkeller719
,
8/1/2011 12:00:00 AM(UTC)
|
0
|
147
|
|
|
|
(Old) After Clicking Continue...
My walls look nothing like the walls in the web video... the walls intersect and overlap each other. I have a pic I can send to explain if possible to send. Also, when placing doors, 1' from a wall does not always look the same... 1' often seems to be rig
Bobbyva
,
7/25/2011 12:00:00 AM(UTC)
|
0
|
253
|
|
|
|
** Tracing a large PDF?
I should have posted this before buying the software :) I have a PDF of a survey for the lot we just purchased... the lot is 1.6acres with a few odd angles, so the dimensions are fairly large and complex. Will this software allow me to do this task so tha
Bobbyva
,
7/20/2011 12:00:00 AM(UTC)
|
0
|
330
|
|
|
|
Important Information:
The Punch Software uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close
