|
** endwall for an arched roof
I am trying to layout an endwall for a fabric building with arched roof 30ft wide arch with 11 ft high center
Crevelt, Dwight
,
11/25/2016 12:00:00 AM(UTC)
|
0
|
130
|
|
|
|
(Old) Setting Wall Dimensioning Properties
I have tried to use this software a few times with limited success.One main problem is trying to set the wall dimensioning properties (when drawing exterior walls) to measure from the outside of the wall (not center, as seems to be the default) and to get
Fabacher
,
4/16/2004 12:00:00 AM(UTC)
|
2
|
203
|
Smith, Dick
3/13/2012 12:00:00 AM(UTC)
|
|
|
(Old) Different ceiling height in same room
I am adding an addition onto our living room (the existing outer wall will be removed). The addition will have a raised ceiling - so the living room with actually have two heights (8 foot and 12 foot at the peak of the addition). I cannot figure out how
Fish, Mac
,
1/10/2011 12:00:00 AM(UTC)
|
3
|
238
|
Fish, Mac
1/20/2011 12:00:00 AM(UTC)
|
|
|
(Old) Grid disappears inside house
What am I doing wrong? If I draw four exterior walls (a box) the grid is no longer shown inside the "box". If I change the walls to interior, the grid appears. If I change them back to exterior, the grid disappears again. Why and is there a "work around"
Machado, John
,
12/4/2005 12:00:00 AM(UTC)
|
3
|
227
|
bagby
7/27/2010 12:00:00 AM(UTC)
|
|
|
(Old) Wall Color
1. It seems that every time I color the inside surface of an exterior wall (eg "paint" a room), the selected color is painted on the entire wall, not just in that particular room. Any fix for that?
2. Slightly off topic, but........ in a previ
tn_yank
,
3/20/2008 12:00:00 AM(UTC)
|
3
|
218
|
Woodman, Crawford
5/4/2009 12:00:00 AM(UTC)
|
|
|
(Old) 2nd level triangular shaped cantilever wall elevation...
... As if that isn't complicated enough, it is located under a half Gambrel/Gable roof. I am working on this finishing piece of the Gable/Gambrel wall of a plan. This is the last piece of the shell of this house and I'm getting erronious 3D representati
Gersenson, Bruce
,
10/27/2008 12:00:00 AM(UTC)
|
0
|
133
|
|
|
|
(Old) layout of house
can i just tell the software i want a house to be 52ft x27ft and will it
draw it also for the size of the rooms
seacapt
,
3/18/2002 12:00:00 AM(UTC)
|
5
|
244
|
Patricia G.
8/14/2008 12:00:00 AM(UTC)
|
|
|
(Old) Can't delete wall segment w/o deleting all walls.
When I select a single exterior wall segment, All the walls get delted. I used the break wall tool to create a break, then tried it and got the same results. FYI, I also cannot delete a door once it's been added. I can undo it right after adding, but in
Egan, Howard
,
9/13/2007 12:00:00 AM(UTC)
|
1
|
446
|
Patricia G.
9/14/2007 12:00:00 AM(UTC)
|
|
|
** 45 deg. angled walls
I used another program 10 yrs. ago, and found it very simple to cut 90deg corners off of exterior walls at a 45 degree angle. I was able to choose the "cut off length" (sorry if the terminoligy is incorrect,, I'm not an engineer) By choosing the length fr
Downey, M
,
5/22/2007 12:00:00 AM(UTC)
|
0
|
155
|
|
|
|
(Old) 1 mile long studs in framing editor
All of my studs in the framing editor look fine except two spots. On the rear of my house there is a 2.7:12 shed dormer on a 10:12 roof. To fill in the sides of the dormer I used a wall profile that has an inverted triangle attached to the top. When I
qwertyasd
,
7/26/2006 12:00:00 AM(UTC)
|
0
|
105
|
|
|
|
(Old) Wall Break Problem
As a former Super user, I was so happy to see the Wall Break feature in Platinum Pro - which I used the Wall Break successfully on the front of the house. Now, I have to break the wall on the right side of the house to define 3 rooms. I keep getting a "P
Joy1950
,
4/24/2006 12:00:00 AM(UTC)
|
2
|
219
|
Joy1950
4/27/2006 12:00:00 AM(UTC)
|
|
|
** My interior walls are floating!!
I had no problem making exterior walls, but now that I'm making interior walls, I can't get them to stay on the floor! They are all floating about 18" off the ground and I can't get them level with the exterior walls - - how do I fix this? Thanks!
prinlisacess
,
4/7/2006 12:00:00 AM(UTC)
|
0
|
138
|
Patricia G.
4/7/2006 12:00:00 AM(UTC)
|
|
|
(Old) Surface Measurements
Is there a way I can set the default measurement from the surface of the walls when I am drawing plans? I am measuring a home from the interior only and every time I create a wall I have to go back and re select the wall and change the measurement to sur
Newville, Trent
,
1/23/2006 12:00:00 AM(UTC)
|
0
|
129
|
Patricia G.
1/23/2006 12:00:00 AM(UTC)
|
|
|
(Old) Punch won't leave my wall alone
I'm trying to add an interior wall from one exterior wall to another, and every time I do, it changes it to an *exterior* wall? If it's going to pull magic on me, it ought to at least pop up something and tell me *why* it thinks it needs to do that so I
Batie, Alan
,
12/9/2005 12:00:00 AM(UTC)
|
0
|
104
|
Patricia G.
12/9/2005 12:00:00 AM(UTC)
|
|
|
(Old) wall segment properties - line types/colors
Hi There, I need to be able to differentiate between walls that are going to be removed and those that are going to stay in plan view. Is there a way that I can change the properties of the wall segment to show up as either a different color or line typ
Marinkovich, Nina
,
7/6/2003 12:00:00 AM(UTC)
|
1
|
192
|
Patricia G.
5/9/2005 12:00:00 AM(UTC)
|
|
Guest
|
Important Information:
The Punch Software uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close
